Greyscale Racing MRCG
http://www.redrc.net/wp-content/uploads/2007/07/greyscaleracingmrcg.jpgComing soon from Greyscale Racing is the MRCG, a pan chassis aimed at open-class racers who need a lower CG, more responsive handling, and more tuning options than a standard Mini-Z. Based on the Mini-Z MR02, the car features a mid motor layout and narrow battery configuration for more responsive handling as well as dual flex plate suspension, similar to that seen in the Mini-Z F1 cars. This is a true race car, with the ability to adjust the weight bias by adjusting the placement of the cells, while the front end of the car allows adjustment of the ride height, independant of the spring preload.Click here for the full feature list…
Features:
- Mid-motor configuration for agile handling
- Narrowest battery configuration possible to increase responsiveness
- Dual flex-plate suspension similar to Mini-Z F1
- Compatability with many rear suspension configurations: side springs, tri-shock system, disk damper, oil damper, or any combination of those
- Battery pack placed far more rearward than in Mini-Z MR02
- Adjustable weight bias by shifting battery pack fore and aft
- Electronics plate cinches down on any AAA or lithium-polymer pack that fits
- Unique 3-piece front end allows ride height to be adjusted fully independently of spring preload and front end maintenance without kingpin removal
- Thin fiberglass tierod and electronics plate, lots of Delrin and minimal hardware used in order to keep chassis weight low
- Compatability with many servos and electronics packages
- 98mm wheelbase
Parts included:
- G10 fiberglass chassis pieces: Main chassis, Front lower bulkhead, 0°, -1° and 1° tierods, Electronics plate, Rear body/damper mount, Body mount clips (2), Flex plates (2), Rear pod bottom plate, Rear pod top plate (for disk damper), Rear pod top plate (no disk damper)
- Delrin pieces: 0° caster blocks, servo mounts, tierod horn, standoffs, differential height adjusters (for rear pod; 4 settings)
- Aluminum pieces: Rear pod left and right side plates
- Hardware: Stainless steel screws and nuts
Additional parts required:
- Mini-Z MR015/02 front knuckles, kingpins, springs, spring perches, c-clips, rear ball differential
- Mini-Z MR01/015/02 wheels, tires, bearings
- Micro servo (no wider than 23mm), servo saver
- Receiver and ESC (or combo), compatible transmitter
- Mounting tape for electronics
- 130-size motor, 48dp 2mm shaft pinion
- Battery pack
- Body
看着不错,应该是纯性能版本而不是追求视觉冲击的,希望上市的时候能带舵机,如果是四线能兼容MINIZ PCB就更牛了!
[ 本帖最后由 321go 于 2007-7-24 09:40 AM 编辑 ] DIY................. 这个设计一点都不新鲜了，后驱车基本没啥大的花样出来。后面的结构有点复杂化了，3条避震＋摩擦板，估计会重不少。不知道车壳是什么材质的。 关键不在于设计是否新鲜,而是终于有量产了,就是不知道能否买到,现在对性能做评价还过早吧 用碳纤维底板的话，量产也不会便宜到那边去吧。。。。。。。。 这样的结构，车身有多少的滚动啊？？！！ 图片转自Mini-ZRacer.com 看起来不错。。不知道跑起来怎么样。最近发现理论和实际还是有区别的。光靠看和想还是不够的。关键还是要去跑 这不是RM马达座吗等于..........好吗?
页:
[1]
2