Mg90s金属齿舵机上身，10多块一个，备用的sg90插上根本没反应http://app.rcfans.com/public/emotion/face_020.pnghttp://app.rcfans.com/public/emotion/face_020.pnghttp://app.rcfans.com/public/emotion/face_020.png，发来就是坏的
http://image.rcfans.com/pic/20200718/1595065192860177_566.jpg
http://image.rcfans.com/pic/20200718/1595065192945252_575.jpg
http://image.rcfans.com/pic/20200718/1595065193276836_974.jpg
转向部分开始制作
http://image.rcfans.com/pic/20200718/1595067492221581_457.jpg
转向部分完成。材料需要打磨，不省心
http://image.rcfans.com/pic/20200718/1595069545370219_13.jpg
http://image.rcfans.com/pic/20200718/1595069545473663_858.jpg
http://image.rcfans.com/pic/20200718/1595069545734535_272.jpg
http://image.rcfans.com/pic/20200718/1595069546000211_954.jpg
前半部分悬挂基本好了，连接拉杆舵机就行了。这设计和大午餐盒真是一脉相承。打印材料拧螺丝真的太痛苦了，好在各零件虚位很小，基本没有，因为大多数拼接都需要打磨http://app.rcfans.com/public/emotion/face_020.pnghttp://app.rcfans.com/public/emotion/face_020.pnghttp://app.rcfans.com/public/emotion/face_020.png
http://image.rcfans.com/pic/20200718/1595072324446845_55.jpg
http://image.rcfans.com/pic/20200718/1595072324762816_640.jpg
http://image.rcfans.com/pic/20200718/1595072325100714_170.jpg
http://image.rcfans.com/pic/20200718/1595072325404585_169.jpg
避震上身，可能弹簧截的长了点，挺的太直
http://image.rcfans.com/pic/20200718/1595078827387547_140.jpg
http://image.rcfans.com/pic/20200718/159507882746082_66.jpg
忘记装前轮的杯头轴了，拆了重装。装上轮子，弹簧没办法修改了，太硬，哈哈，看着很可爱
http://image.rcfans.com/pic/20200718/1595083769207426_752.jpg
http://image.rcfans.com/pic/20200718/1595083769279930_844.jpg
http://image.rcfans.com/pic/20200718/1595083769497757_741.jpg
http://image.rcfans.com/pic/20200718/1595083769798496_106.jpg
进入关键环节，祭出我的跑死马和金属马达齿http://app.rcfans.com/public/emotion/face_003.pnghttp://app.rcfans.com/public/emotion/face_003.pnghttp://app.rcfans.com/public/emotion/face_003.png
http://image.rcfans.com/pic/20200718/1595083925344410_574.jpg
慢慢打开，这色调，这色彩，真是喜欢。电机齿也很精致，把玩很不错。最后和电机架合个影，远看像碳纤，配合镂空的电机后盖，仿佛已经抬头抬翻了，空翻没有抱希望，哈哈哈http://app.rcfans.com/public/emotion/face_005.pnghttp://app.rcfans.com/public/emotion/face_005.pnghttp://app.rcfans.com/public/emotion/face_005.png
http://image.rcfans.com/pic/20200718/1595084493696439_726.jpg
http://image.rcfans.com/pic/20200718/1595084493869340_474.jpg
http://image.rcfans.com/pic/20200718/1595084494091722_513.jpg
http://image.rcfans.com/pic/20200718/159508449435888_414.jpg
http://image.rcfans.com/pic/20200718/1595084494576535_796.jpg
http://image.rcfans.com/pic/20200718/1595084494979387_380.jpg
http://image.rcfans.com/pic/20200718/1595084495233265_141.jpg
http://image.rcfans.com/pic/20200718/1595084495464957_511.jpg
http://image.rcfans.com/pic/20200718/1595084495713801_656.jpg
抬头轮杆子又滑了一个丝，换上大一号螺丝继续干，完美贴合。
http://image.rcfans.com/pic/20200719/1595095471736987_375.jpg
http://image.rcfans.com/pic/20200719/1595095471842304_391.jpg
http://image.rcfans.com/pic/20200719/1595095472236121_337.jpg
http://image.rcfans.com/pic/20200719/1595095472544514_493.jpg
这个驱动的部分是最难装的，要用机米去对打磨的轴上的凹槽，对不准就卡不紧，对准了有时候又滑丝。装坏了两个零件，还好卖家给力，多给了几个。毕竟材料，性质不稳定，有的硬，有的太硬，有的里面没有打好，有点空。只能说材料太硬了，车又小，里面的螺丝孔位都是过盈的，装起来非常结实，基本没有什么虚位。
|
|