DIY低成本蚊车赛道
总的成本也就60块钱......http://image.rcfans.com/pic/20201021/1603286500797408311.jpg?x-oss-process=image/watermark,image_cGljLzIwMjAwNzIxL29zc18xNTk1MzM4ODExNTY2XzIzMl8xMThfMzI2LnBuZw==,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20201021/16032865015215729.jpg?x-oss-process=image/watermark,image_cGljLzIwMjAwNzIxL29zc18xNTk1MzM4ODExNTY2XzIzMl8xMThfMzI2LnBuZw==,t_50,g_se,x_20,y_20
PVC买的最便宜的那种摄影用的
http://image.rcfans.com/pic/20201021/1603286681947346540.jpg?x-oss-process=image/watermark,image_cGljLzIwMjAwNzIxL29zc18xNTk1MzM4ODExNTY2XzIzMl8xMThfMzI2LnBuZw==,t_50,g_se,x_20,y_20 然后买了4条EVA的边条,规格如图
http://image.rcfans.com/pic/20201021/1603286753073309415.jpg?x-oss-process=image/watermark,image_cGljLzIwMjAwNzIxL29zc18xNTk1MzM4ODExNTY2XzIzMl8xMThfMzI2LnBuZw==,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20201021/1603286753075271464.jpg?x-oss-process=image/watermark,image_cGljLzIwMjAwNzIxL29zc18xNTk1MzM4ODExNTY2XzIzMl8xMThfMzI2LnBuZw==,t_50,g_se,x_20,y_20 1.先用铅笔画一个大概的图,越简单越好,复杂了赛道窄了反而不好漂移,这赛道有个好处就是干净,便宜,还不伤车壳车架!
2,画好后,可以直接折弯EVA边条,折一下大概的那种弧度,尽量折的大一点,然后用吹风机吹热一下有助于轮廓定型!
3,清洁pvc表面,并保持干燥!
4,把粘纸撕掉用吹风机热风吹一下胶面,顺着自己画的路线粘,接头处补一点双面胶,防止脱胶变形!
http://image.rcfans.com/pic/20201021/1603287095510518557.jpg?x-oss-process=image/watermark,image_cGljLzIwMjAwNzIxL29zc18xNTk1MzM4ODExNTY2XzIzMl8xMThfMzI2LnBuZw==,t_50,g_se,x_20,y_20 EVA可以折很大角度的,所以不用担心折坏了!
记得PVC一定得磨砂的,磨砂面比光滑面更滑!
http://image.rcfans.com/pic/20201022/1603332589959027626.jpg?x-oss-process=image/watermark,image_cGljLzIwMjAwNzIxL29zc18xNTk1MzM4ODExNTY2XzIzMl8xMThfMzI2LnBuZw==,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20201022/1603332590677414674.jpg?x-oss-process=image/watermark,image_cGljLzIwMjAwNzIxL29zc18xNTk1MzM4ODExNTY2XzIzMl8xMThfMzI2LnBuZw==,t_50,g_se,x_20,y_20 Pvc铺不平吧 守望者7777 发表于 2020-10-22 11:26
Pvc铺不平吧
收到后是一卷的,反过来用吹风加热平铺放两天就平了https://app.rcfans.com/public/emotion/face_007.png
看着很有质感的小跑道,赞 不错不错https://app.rcfans.com/public/emotion/face_068.pnghttps://app.rcfans.com/public/emotion/face_068.png
页:
[1]