HOCHUNGYAN 发表于 22-3-20 17:50:00

K7 Newton

今天把舵机裝好，下一步是电机和固定接收机
http://image.rcfans.com/pic/20220320/1647769753755382768.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20220320/1647769778038203465.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20220320/1647769797724894122.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20

XMX/// 发表于 22-3-24 18:01:46

为大佬点赞

HOCHUNGYAN 发表于 22-3-24 18:10:01

原机木电机座跟无刷电机的支架的螺丝孔是对不上的，唯有用熱溶胶搞定
http://image.rcfans.com/pic/20220324/1648116513017013999.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20

HOCHUNGYAN 发表于 22-3-25 23:35:24

电机未飞先壞了，本来好好的，装好后加油卡卡卡，檢查后发觉里面有一个銲点离銲了，拆开后又分不开綫圈和底坐
http://image.rcfans.com/pic/20220325/1648222514363124130.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20220325/1648222514673259129.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20220325/1648222514987305471.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20

榴莲 发表于 22-5-14 17:49:33

用热熔胶会不会太重？

HOCHUNGYAN 发表于 22-7-7 21:36:41

榴莲 发表于 2022-05-14 17:49
用热熔胶会不会太重？

重量不是问题，关键结構不行
页: [1]
查看完整版本: K7 Newton